Some Notes on the Remuneration of Structural Engineers & Architects
Date published

N/A

First published: N/A

Price

Standard: £9 + VAT
Members/Subscribers: Free

Buy Now

Added to basket

Back to Previous

Some Notes on the Remuneration of Structural Engineers & Architects

The Structural Engineer
Some Notes on the Remuneration of Structural Engineers & Architects
Date published

N/A

First published

N/A

Price

Standard: £9 + VAT
Members/Subscribers: Free

Buy Now

The labourer, be he millionaire or manual worker, is worthy of his hire, but, in the absence of a definite contract, very distinct divergences of opinion may arise as to the value of that hire. Such value may ultimately have to be settled by Judge and Jury, and possibly, in the case of a Structural Engineer or Architect, the award may be on such a scale as to make the victorious Plaintiff feel that the hire is not worthy of the labourer. Lexterus

Additional information

Format:
PDF
Publisher:
The Institution of Structural Engineers

Tags

Issue 8

Related Resources & Events

The Structural Engineer
The Structural Engineer as Artist. Chapter VIII. - The Unconditioned Aggregate

The Structural Engineer as Artist. Chapter VIII. - The Unconditioned Aggregate

IN the first of the chapters of this series which dealt with the subject of factory design I divided industrial building into four elements, the factory block, the industrial hall, the factory stack, and the unconditioned aggregate. A. Trystan Edwards

Author - Edwards, A Trystan
Price - £9
The Structural Engineer
The Lateral and Transverse Bracing of Bridges, III

The Lateral and Transverse Bracing of Bridges, III

The introduction of special braking girders into the floor system of large span bridges is of comparatively recent practice. A brief notice of this detail as applied in the Hell Gate Bridge may be of interest. The Hell Gate Bridge is a two-hinged steel arch of 977 ft. 6 in. span between bearings. The floor carries four railway tracks between the main ribs and two bracketed side walks projecting 16 ft. 6 ins. on the outsides of the main ribs, which are 60 ft. apart, centre to centre. The total width is thus 93 ft. between centres of parapet girders. The spacing of cross-beams is 42 ft. 6 ins., and their weight upwards of 80 tons each. The four cross-beams adjacent to the abutments, that is, up to the points G and G, Fig. 20, where the lower chords of the arch rise above the roadway, are framed in between the vertical struts of the arch ribs. The remaining cross-beams over the middle portion of the span are suspended from the arch ribs by suspenders hung to pin joints so arranged as to permit freedom of transverse movement, Fig. 21. The suspended portion of the floor, therefore, would possess no inherent lateral stability in the absence of a lateral bracing system. This method of suspension was adopted to avoid bending stresses in the suspenders due to vertical deflection of the floorbeams and horizontal deflection of the floor lateral system. The suspenders are further made slender in elevation in order to minimise bending stresses due to the longitudinal expansion and contraction of the floor. The floor lateral bracing consists of stiff diagonals in the plane of the bottom flanges of the railroad stringers, as indicated by the heavy lines in the plan, Fig. 20. These diagonals are riveted to the stringers and cross-beams at the intersection points. The lateral system thus forms a rigid horizontal girder between panel points 3 and 6, but owing to the transverse flexibility of the suspenders, the portion of the lateral system between panel points 3 and 6 is called upon to act as a horizontal cantilever for restraining lateral deflection of the suspended portion of the floor. At panel point 6 an expansion joint is introduced in all longitudinal floor members and the diagonal lateral system coming from the right terminates at P in a pocket on floor-beam No. 6, so arranged as to prevent lateral movement whilst allowing longitudinal sliding to take place. The point P therefore receives the horizontal reaction from the central portion of the lateral system and transfers it as a concentrated load to the cantilever portion between panel points 3 and 6. At the corresponding panel point No. 17, on the opposite side of the centre of span, only partial freedom of movement of the lateral system is provided for. Expansion joints are introduced in the parapet girders at E, E, and in the side-walk stringers, but the diagonal joint at P1, and the railrotad stringers at cross-beam No. 17 are riveted. The floor lateral system between P and P, therefore, acts very sen

Author - Husband, J
Price - £9
The Structural Engineer
The Essentials of Reinforced Concrete Design. Part III. - T Beams with Tension Reinforcement Only

The Essentials of Reinforced Concrete Design. Part III. - T Beams with Tension Reinforcement Only

In the rectangular reinforced concrete beam, the concrete below the neutral axis, while adding to the dead weight of the construction, does not add to the bending resistance. Ewart S. Andrews

Author - Andrews, Ewart S
Price - £9